Did you just start up your chainsaw for the first time this season, and it’s not pulling oil as it should? This can be a frustrating problem to diagnose and fix. But don’t worry, we’re here to help! In this post, we’ll walk you through some of the most common causes of a chainsaw bar not getting bar oil, as well as what you can do to fix them.
Moreover, we will also discuss oiling the chainsaw blade. So read on, and get your chainsaw back up and running in no time!
What do you mean by chainsaw bar not getting oil?
If the chain on your chainsaw is not being lubricated properly, it can cause a lot of problems. The first thing you’ll notice is that the saw will start to produce more smoke than usual.
This is because the lack of oil is causing the chain to heat up and burn through the wood more quickly. In addition, the chain will also start to stretch and wear out more quickly. If left unchecked, this can eventually lead to the chain breaking entirely.
What is a Chain Oiler?
A chain oiler is a device that helps deliver oil to the chain while you’re using the saw. It’s usually located near the handle of the saw and consists of a small reservoir filled with chainsaw oil. As you use the saw, the oil is slowly drawn out of the reservoir and onto the chain. This helps keep the chain lubricated and prevents it from overheating or breaking.
How chainsaw oiler works?
Most chainsaw oilers work using a simple gravity-fed system. The oil is stored in a small reservoir, and as you use the saw, gravity pulls the oil out of the reservoir and onto the chain.
Some saws also have a pump-driven system, which helps force the oil onto the chain even when the saw is not in use. This can be helpful if you’re going to be storing the saw for an extended period of time (such as over winter).
How to Test Your Oil Pump?
If your saw has an oil pump, it’s a good idea to test it before each use. To do this, simply turn on the pump and let it run for a few seconds. Then, check to see if there is any oil coming out of the pump. If not, then you’ll need to replace the pump.
How to adjust bar oil on the Stihl chainsaw?
If your bar oil is leaking from the saw, it means you need to adjust the tension on the chain. To do this, loosen the screws on the side of the bar until the chain can be moved freely.
Hold the chain against the guide bar and tighten the screws until it is snug. You should also check for proper lubrication of your chain every time you refuel. Make sure you apply a light coat of oil to each link, using 10-12 drops per 10 inches of chain. Avoid over-oiling, as this will only create a fire hazard.
How to clean a chainsaw?
First, determine what type of oil is on your chain saw. If it is general-purpose cutting oil, proceed to Step 2. If it is specialized logging chain oil, go to Step 3.
Step 2: General-Purpose Cutting Oil
Chain saws, used for woodcutting, require special care to keep them running at peak efficiency and prolong their life. To clean a chain saw that is covered in general-purpose cutting oil:
- Disconnect the spark plug wire from the spark plug so the saw cannot start accidentally.
- Turn the saw on its side and unscrew the screws that hold the guide bar and chain in place. The guide bar is held in by two screws at the bottom of the housing; the chain is held in by one screw at the top.
Remove the guide bar and chain from the saw.
Wash all parts in a pan of hot water and dishwashing soap. A toothbrush can be used to scrub away any stubborn dirt or oil buildup.
- Rinse all parts thoroughly with clean water.
- Dry all parts with a clean rag.
- Reassemble the saw, being sure to tighten all screws securely.
Specialized logging chain oil is designed to stay on the chain longer and resist being thrown off by the centrifugal force of the spinning chain. This makes it ideal for use in extremely dusty or dirty conditions. However, it can also make the chain difficult to clean.
Why is My Chainsaw Oiler Not Working
Chainsaw stop working? it could be because the reservoir is empty. Make sure to check the level of oil in the reservoir before each use, and refill it as needed. It’s also possible that the delivery tube or pump is blocked, preventing the oil from reaching the chain.
You can try cleaning out the delivery tube with a paperclip or similar object. If that doesn’t work, you may need to replace the entire chain oiler assembly.
Why is my Stihl chainsaw not oiling the bar?
One common reason a Stihl chainsaw doesn’t oil the bar is that the saw isn’t getting enough fuel. If the fuel/oil mix is too rich, it will gunk up the small holes in the oil pump and prevent it from putting oil on the chain.
Other reasons a chainsaw might not be oiling properly include a dirty air filter, low compression, or a clogged fuel line. If you’re having trouble figuring out why your chainsaw isn’t oiling, it’s best to take it to a trained technician who can troubleshoot the problem and fix it.
Chainsaw Bar Not Getting Oil – FAQs
Our Verdict
As you can see, there are a few different things that can cause a chainsaw bar not to get oil. But don’t worry, with a little troubleshooting you should be able to identify and fix the problem in no time. And if you ever have any other questions about your chainsaw, feel free to give us a call! We’re always happy to help.
