How to Put a Chain Back On a Chainsaw – A Step By Step Guide

Maintaining your chainsaw is essential to keeping it in good working order. One of the most important tasks you’ll need to do is to put the chain back on correctly after sharpening it. This step-by-step guide will show you how to do just that. Keep your chainsaw running smoothly by following these simple instructions!

How to remove the chain from a chainsaw?

1. First, make sure that the chainsaw is turned off and unplugged.
2. Next, find the tensioning knob or screw and loosen it. This will allow you to remove the old chain.
3. Carefully take the old chain off of the saw’s bar. If it is difficult to remove, you may need to use a pair of pliers.
4. Once the old chain is off, inspect it for damage. If it is excessively damaged, you will need to replace it.
5. If the old chain is not excessively damaged, you can proceed to the next step.

How to Put a Chain Back on a Chainsaw?

So how do you put chains on chainsaws?

1. Before you begin, make sure the chainsaw is turned off and unplugged.
   
2. Locate the chain brake and release it by pushing the small button on the side of the chainsaw.
   
3. Lift up the front handle of the chainsaw and locate the chain cover release lever, which is near where the cover attaches to the saw body. Push this lever forward and away from the saw body to remove the cover.
   
4. Check that both sides of the chain are properly lined up with each other – if one side is off, turn off the saw and realign them before continuing
   
5. Carefully place one hand on top of each bar clamping screw (near where you hold onto to start/stop the engine) and unscrew them until they are loose enough to slip the chain over but still tight enough so it won’t move around when the engine is running
   
6. Remove the old chain from around the clutch sprocket wheel by gently pushing down on chain breaker pins (should be sticking out about 1/8 inch) then pull the old chain off the wheel – use a screwdriver or similar tool if needed.
   
7. Slip new chain over wheel ensuring that both ends of link plates are in the groove on either side of the wheel – do not push links together yet!
   
8. Holding onto bar clamps screws with the same hand as before, tighten screws until links are tight against the wheel – do not over-tighten or you’ll damage links! The chain should now be clamped in position
   
9. Slip Chain Breaker Pins back into newly formed holes in links (they may need slight adjustment) until they protrude about 1/8 inch past the outer surface of the link plate – if pins are too long they will prevent proper operation of a chainsaw; too short and they’ll break off easily during use. Now your new chain is ready for cutting!
   

Now that you know how to put a chain back on a chainsaw, you can keep your saw in good working order. Be sure to follow these steps carefully and always check the manufacturer’s instructions for more information.

Why is it essential to maintain your chainsaw?

Chainsaws are one of the most versatile and useful tools you can own, but they require regular maintenance to keep them running smoothly. A well-maintained chainsaw will last longer and perform better, making your life easier in the long run. Neglecting your chainsaw can lead to expensive repairs or even dangerous accidents.

Tips for keeping the chain on the chainsaw

• Always follow the manufacturer’s instructions for your particular chainsaw model.
• Keep the chain sharpened and lubricated according to the manufacturer’s recommendations. A dull chain will not only make your saw less effective, but it can also be dangerous.
• Inspect the chain regularly for damage and replace it if necessary. A damaged chain can cause the saw to kick back, which can be very dangerous.
• When not in use, store your chainsaw in a dry, safe place where it will not be damaged.

By following these tips, you can help ensure that your chainsaw will be ready to use when you need it.

How to put a chain back on an electric chainsaw?

1. Unplug the chainsaw from the power source.
2. Remove the guide bar and chain from the saw.
3. Inspect the guide bar and chain for damage. If it is excessively damaged, you will need to replace it.
4. If the old chain is not excessively damaged, you can proceed to the next step.
5. Place the new chain around the sprocket on the guide bar.
6. Make sure that both ends of the link plates are in the groove on each side of the sprocket. Do not push them together yet!
7. Hold onto both ends of the chain with one hand and pull tight. The links should be tight against the sprocket but not excessively tight.
8. Push the chain breaker pins back into the newly formed holes in the links (they may need slight adjustment) until they protrude about 1/8 inch past the outer surface of the link plate. If they are too long, they will prevent proper operation of the chainsaw; too short and they will break off easily during use.
9. Plug the chainsaw back into the power source and you are ready to start cutting!

How to Put a Chain Back on a Chainsaw – FAQs

Conclusion

So, there you have it. You should now be able to put a chain back on your chainsaw like a pro. If you’re feeling confident and want to practice before attempting the real thing, we suggest trying it out on an old piece of wood first. Remember to always take care when using any power tool and stay safe while you work!