Chainsaws are a great way to cut through thick branches or logs with ease. However, before you can start using your chainsaw, there are a few things you need to do first. In this post, we will show you how to start a craftsman’s chainsaw. We will also go over the proper maintenance routine for your chainsaw to keep it running smoothly. Moreover, we will discuss how do you start a chainsaw and how to crank a chainsaw. Let’s get started!
How to Put a Chain on a Craftsman’s Chainsaw?
Step 1: Ready the Saw
Make sure that your chainsaw is in a well-ventilated area and there are no flammable materials nearby. Put on your gloves and make sure you don’t have any loose jewelry or accessories on. Turn off the chainsaw and let it cool down for several minutes before attempting to install a new chain.
Step 2: Installing the New Chain
Remove the bar cover, if your chainsaw has one, and carefully remove the old chain from the saw. Use a wire brush to clean off any dirt or debris that is lodged in between the bar and guide using a mixture of water and lighter fluid.
Once you have done this, place the new chain on the bar and line up the drive links. Make sure you don’t damage the sprocket with your hands as you turn it clockwise to tighten it. Once it is tight enough, use a pair of locking gloves or clamp to hold the bar in place. You can now proceed to remove your locking tools and replace your bar cover.
Step 3: Get Ready To Start the Chainsaw
Once the chain is installed, you are ready to get started. Be sure that your chainsaw is not in an area where it could cause damage to people or objects around you before you attempt to start it up.
Check to make sure that it has a full tank of gasoline and a charged battery. You should also make sure your chainsaw is properly lubricated before you start up the engine to reduce wear and tear on the internal components.
Step 4: Prepare To Start The Engine
Before you can actually start using your chainsaw, you need to do a bit of prep work. A good place to start is the choke button on the handle of your chainsaw. The first time you start it up, make sure that the knob is in a vertical position with the tab at the top.
This will ensure that there is enough fuel getting into the engine to keep it running smoothly without flooding or stalling. You should also make sure that your chainsaw is not running in an area with a lot of dust or debris, as it could do some damage to the moving parts.
Step 5: Start Your Chainsaw
To start the chainsaw, you should first put on your gloves and safety glasses. Next, you will want to move any tools and materials away from the area you are about to use your chainsaw in. Make sure that you have dried off the bar and chain with a rag before you start up your chainsaw.
Then, pull out the choke knob on the handle of your chainsaw until it is fully extended. Now, press the primer button 5-8 times depending on what type of chainsaw you have. Hold the compression release valve and pull the starter cord out until it engages.
Let go of the compression release button, but keep your hand on it as you start up the chainsaw to prevent any accidental starting. If done properly, your chainsaw should start up immediately.
How to Start a Craftsman Chainsaw – Step-by-Step Guide:
Starting a chainsaw can be dangerous if done improperly. Make sure you are wearing protective clothing and eyewear before attempting to start your chainsaw.
Follow along with our steps below to learn how to start your new chainsaw!
Step 1: Choke Button Positioning
Make sure that the chock button on the handle is pushed in and the knob is vertical.
Step 2: Primer Button
Locate the primer button, on most chainsaws, it will be located on the top of the handle. Press this 5-8 times depending on your model.
Step 3: Compression Release Knob
Pull this knob out until it fully extends and then let go.
Step 4: Pull Out Starter Cords
Hold the compression release button and pull out the starter cord until it is engaged. Let go of the compression release valve, but keep your hand on it as you start up your chainsaw to prevent any accidental starts.
Step 5: Start Your Chainsaw with a Push of a Button
Once the chainsaw starts, let go of the compression release button and you’re ready to get started!
How to Start a Craftsman Electric Chainsaw?
To start a craftsman electric chainsaw, you’ll need to locate the on/off switch. This is typically a red button located on the rear handle of the saw. After locating the switch, hold it down and pull the starter cord slowly until you feel resistance.
Then, quickly release the switch and pull the starter cord again. You should keep trying until the chainsaw starts. If it doesn’t start after several tries, check to make sure that you have inserted the plug into an outlet and that the outlet is working properly.
How to Rebuild a Craftsman Chainsaw Carburetor?
There are some very good tutorials online with step-by-step guides on how to rebuild the carburetor. There are also replacement carburetors that can be purchased for less than $20.00 and they will come pre-assembled with all of the parts needed so you won’t have to rebuild it yourself.
Step 1- Removing the Carburetor
Remove the carburetor from the chainsaw by first taking off the plug wire and then removing the retaining clip. Then, remove the nuts that hold it in place and pull it out of the chainsaw. Once you have taken off the carburetor, set it aside somewhere where you won’t lose any of its parts.
Step 2- Cleaning the Choke Tube
Clean out any dirt or debris from the choke tube by spraying it with a carburetor cleaner and using a toothbrush or other small brush to get into all of the crevices. Rinse off the cleaner when you are done, but make sure most of it evaporates before you put it back on the chainsaw.
Step 3- Removing the Float Bowl Cover
Remove the nut that holds this piece in place and pull it out of the carburetor along with its gasket. Use a screwdriver or other flat object to scrape off any debris from inside before you put it back on.
Step 4- Removing the Spring
Remove the spring from the carburetor by pulling it up and out of its seat. You may need to use a pair of needle-nose pliers, depending on how well they will pull out.
Step 5- Removing the Needle and Seat
Using a small screwdriver or tweezers, remove the needle and seat from the carburetor.
Step 6- Replacing the Needle and Seat
Put in a new needle and seat to replace the old one when you are done cleaning it, making sure that they go back in where they came from when you remove them.
Step 7- Putting It All Back Together
Replace all of the parts in reverse order and you should be finished. Test out the chainsaw and see if it starts up better than before.
The engine components in your chainsaw are vital for its operation, so when they become worn out or damaged, finding the right replacement parts is absolutely necessary.
Why won’t my Chainsaw Chain Tighten?
It’s possible that the chain is too tight. Chainsaw chains are designed to be run a little bit lose so that they will cut better. If the chain is too tight, it will bind and not cut well. You can tell if the chain is too tight by checking to see if it binds up when you try to spin it by hand.
If the chain is not too tight, then it could be that the bar oil has been depleted.
Chainsaw chains require a continuous stream of oil to keep them lubricated and free-moving. If there isn’t enough oil, the chain will start to wear down and will eventually break.
To check if your chainsaw needs more oil, lubricate the bar with a few drops. Spin the chain by hand and make sure that it spins smoothly. If the chain still binds, then there isn’t enough bar oil. Add more oil and continue using it.
How to start a craftsman chainsaw – FAQs
Our Verdict:
A Craftsman chainsaw is a very versatile tool and can be used to cut down thick tree stumps or saplings as well as delicate fruit branches. Chainsaws are one of the most dangerous tools that you will find yourself using, so being able to start them up safely and efficiently is imperative.
